IEI PSC-586VGA

PSC-586VGA ™ All Rights Reserved. Manual first edition May 05,1996 The information in this document is subject to change without prior notice in order to improve reliability, design and function and does not represent a facturer. In no event will the manufacturer be liable for direct, indirect, special, incidental, or consequential damages arising out of the use or inability to use the product or documentation, even if advised of the possibility of such This document contains proprietary information protected by copyright. All rights are reserved. No part of this manual may be reproduced by any mechanical, electronic, or other means in any form without prior written permission of the manufacturer. PSC-586VGA is registered trademarks of Acquire Inc.,IBM PC is a registered trademark of International Business Machines Corporation. Intel is a registered trademark of Intel Corporation. AMI is registered trademarks of American Megatrends, Inc. Other product names mentioned herein are used for identification purposes only and may be trademarks and/or registered trademarks of their respective companies. Trademarks damages. commitment on the part of the manu @Copyright 1996 Single Board Computer w/ VGAISA/PCI Pentium Contents .................................................................3 1.1.........................................................................................4 1.2......................................................................................5 ...................................................................6 2.1...........................................................................6 2.2..............................................................................................8 2.3er Description................................................................................9 2.4.........................................................10 2.5 Upgrade the External Cache.................................................................11 2.6.......................................................................11 2.7.................................................................................11 2.8..............................................12 2.9............................................................................12 ................................................................13 3.1...............................................................13 3.2....................................................................14 3.3Parallel Port.........................................................................................15 3.4Serial Ports..........................................................................................15 1 IDE Disk Drive Connector Floppy Disk Drive Connector 3. Connection PCI VGA Controller FDC37C665/ALI M5113 Multi-I/O Chip Watch-Dog Timer System Memory DRAM Setting the CPU of PSC-586VGA Jump Unpacking 586VGA's LayoutPSC- 2. Installation What You Have Specifications 1. Introduction 3.5.............................................................................16 3.6External Switches and Indicators..........................................................16 3.7External Speaker..................................................................................17 3.8se Port .................................................................................17 3.9...................................................................................18 .......................................................19 4.1Getting Start........................................................................................19 4.2Standard Setup.....................................................................................20 4.3...................................................................................21 4.4Chipset Setup.......................................................................................23 4.5Peripheral Setup...................................................................................25 4.6Power Management Setup....................................................................26 .....................................27 2 Appendix A. Watch-Dog Timer Advanced Setup 4. AMI BIOS Setup VGA Connector PS/2 Mou Keyboard Connector 1 Introduction Welcome to the PSC-586VGA ISA/PCI Pentium w/VGA Single Pentium CPU and advanced high performance multi-mode I/O, that want to provide all the performance, reliability, and quality An advanced high performance super AT I/O chip SMC parallel port and IDE interface are compatible with IBM PC/AT to get the most high performance. User will not need extra VGA card to release one PCI slot for other application. In addition, the PSC-586VGA provides four 72-pin SIMM sockets for 16MB, and 32MB SIMM. So, the total on-board memory can be 3 which are 100% ISA/PCI compatible chipset. PSC-586VGA uses the ALI chipset, M1511/M1512/M1513, configured from 2MB to 128MB. its on-board DRAM. The 72-pin accepts 1MB, 2MB, 4MB, 8MB, accelerator. The VGA controller based on the internal PCI bus The on board VGA controller is Cirrus CL-GD54M30 graphics multiple low power down modes. sophisticated power control circuitry(PCC). The PCC supports and XT architecture's. The FDC37C665 or M5113 incorporates Both on-chip UARTs are compatible with the NS16C550. The FDC37C665 or ALI M5113 is used in the PSC-586VGA board. at a reasonable price. designed for the system manufacturers, integrators, or VARs equipped with high performance factor board, which comes Board Computer. The PSC-586VGA board is an ISA/PCI form 1.1 Specifications : The PSC-586VGA ISA/PCI Pentium w/ VGA Single Board Computer · : Pentium 75-166Mhz · : ISA bus and PCI 32-bit local bus ·DMA channels : 7 ·Interrupt levels : 15 · ·Real-time clock/calendar : DS-12887 chip and quartz oscillator, 128B CMOS memory, powered by lithium battery for over 10 years of data retention. ·RAM memory · Standard Cache RAM Module ·E-IDE hard disk drive interface : up to four PCI Ehnace IDE hard drives. ·Floppy disk drive interface : two 2.88 MB, 1.44MB, 1.2MB, 720KB, or 360KB floppy disk drives. · : NS16C550 compatible UARTs ·Bi-directional Parallel Port ·VGA Controller - GD54M30 : Bus : PCI bus Resolution : 1024x768 - 16 color(512KB VRAM) 256 color(1MB VRAM) 1280x1024 - 16 color(1MB VRAM) Feature Connector : 26-pin hearder on board 4 Two high speed Series ports : 256KB/512KB/1MB Pipelined Burst andSecond Cache memory : 2MB to 128MB,EDO and standard DRAM supported : M1511/M1512/M1513Chipset Bus CPU provides the following specification: ·Watch-dog timer : can be set by 1,2,10,20,110 or 220 seconds trigger the timer. Your program use hex 043 and 443 to control the · ·Mouse : PS/2 Mouse Port on-board. · : +5V @ 4.2A ( Pentium-100,16MB EDO RAM) ±12V @ 15mA ( for RS-232 only) ·Operating Temperature : 0 ° ~ 60 ° 1.2What You Have In addition to this includes the following items: ·PSC-586VGA ISA/PCI Pentium w/ VGA Single Board · · ·VGA utility diskette · If any of these items is missing or damaged, contact the dealer from whom you pur product in the future. 5 materials and carton in case you want to ship or store the chased the product. Save the shipping 6-pin Mini-Din to 5-pin Din Keyboard Adapter Cable FDD/HDD Cable RS-232/Printer Cable Computer , the PSC-586VGA packageUser's Manual C ( CPU needs Cooler) Power Consumption Keyboard connector watch-dog and generate a system reset. period. Reset or NMI was generated when CPU did not periodically 2 Installation information that you should be careful is described. The 2.1PSC-586VGA's Layout < reference next page > 6 and watch dog timer, are also included. configuration, such as CPU type selection, system clock setting, jumpers and switches setting for the PSC-586VGA's the layout of PSC-586VGA is shown, and the unpacking This chapter describes how to install the PSC-586VGA. At first, 2.2 7 Unpacking Your PSC-586VGA Single Board Computer contains sensitive In this section, we describe the precautions you should take while unpacking, as well as during installation. It is very important that the The system board should be done on a grounded anti-static mat. The operator should be wearing an anti-static wristband, grounded at the same point as the anti-static mat. Inspect the cardboard carton for obvious damage. Shipping and handling may cause damage to your board. Be sure there are no shipping and handing damages on the board before processing. After opening the cardboard carton, exact the system board and place it only on a grounded anti-static surface component side up. Again inspect the board for damage. Press down on all the socketed IC's to make sure that they are properly seated. Do this only with the board place on a firm flat surface. Computer. 8 You are now ready to install your PSC-586VGA Single Board DAMAGED. Note : DO NOT APPLY POWER TO THE BOARD IF IT HAS BEEN successfully install the board. instructions be followed correctly, to avoid static damage, and to electronic components that can be easily damaged by static electricity. You can change the PSC-586VGA's configuration by setting jumper switches on the board. The board's jumpers are preset at the factory. Under normal circumstances, you should not need to change the jumper settings. A jumper switch is (sometimes referred to as shorted with the plastic cap inserted over two pins of the jumper). A jumper is with the plastic cap inserted over one or no pin(s) of the jumper. this chapter. CLOSED OPEN 1 1 1-2 2-3 1 1 1 2 2 2 3 3 3 2-3 1-2 2-4 Figure 2.2 9 Figure 2.2 below shows different jumper settings which will be used in open closed 2.3 Jumper Description 2.4 Setting the CPU of PSC-586VGA · CPU Clock Setting : JP6 JP8 JP10 JP10 1-2 3-4 50Mhz/ - 75 OPEN OPEN * 60Mhz/ - 90 CLOSE 66Mhz/ -100 OPEN OPEN OPEN 60Mhz/ -120 OPEN OPEN OPEN OPEN 66Mhz/ -133 60Mhz/ -150 OPEN 66Mhz/ -166 OPEN · CPU Voltage Selection - 2.5V, 2.9V, 3.3V,or 3.45V Please note the 2.5V/2.9V is designed for the future dual supply CPU operation. The dual supply CPU requires 2.5V for CPU core logic and 3.3V for I/O. JP3 JP4 JP5 7 - 8 2.5V 1-2 2-3 9 - 10 (P55C) 11 - 12 7 - 8 2.9V 1-2 1-2 9 - 10 11 - 12 1 - 2 * 3.3V 1-2 2-3 3 - 4 5 - 6 1 - 2 3.45V 2-3 2-3 3 - 4 5 - 6 · CPU type setting (reserved) : CPU Type JP7 *P54C/K5 OPEN M1 10 CLOSE (*) : default setting CPU Voltage (*) : default setting CLOSE CLOSE CLOSE CLOSE CLOSE CLOSE CLOSE CLOSE CLOSE CLOSE CLOSE OPEN OPEN OPEN CLOSE CLOSE CPU Clock/Operation The PSC-586VGA designed pipelined burst Cache RAM The slot is U3. When you install the Cache RAM module, ‘ have compatible problem. And please set the cache Cache Type JP1 JP2 Async. Cache 1-2 OPEN * Sync. Cache 2-3 CLOSE 2.6 System Memory DRAM(EDO RAM supported) There are four 72-pin SIMM sockets to accept . Customers have to install , SIMM Socket 1,2 or 3,4. From left side to right side,the SIMM sockets are SIMM 1, SIMM 3,SIMM 2,SIMM 4. 2.7 Watch-Dog Timer The Watch-Dog Timer is enabled by reading port 443H. It should be triggered before the time-out period ends, otherwise it will assume the program operation is abnormal and will issue a reset signal to start again, or activate NMI to CPU. The Watch-Dog Timer is disable by reading port 043H. · JP13 : Watch-Dog Active Type Setting * 1-2RESET WHEN WDT TIME-OUT 11 DESCRIPTIONJP13 at least 2pcs RAM module on board The total capacity is from 2MB to 128MB 1MB,2MB,4MB,8MB,16MB,or 32MB memory modules. (*) default setting RAM module to Async. or Sync. jumper setting correctly. s quality and performance is no good,will possibleRAM module please try to test it before you buy it. Because some Cache slot to accept 256KB,512KB,1MB Cache RAM module. 2.5 Upgrade the External Cache (*) : default setting 2-3 OPEN · 1-2 3-4 5-6 7-8 1 sec. OPEN OPEN CLOSE OPEN 2 sec. OPEN OPEN CLOSE CLOSE *10 sec. OPEN CLOSE OPEN OPEN 20 sec. OPEN CLOSE OPEN CLOSE 110 sec. CLOSE OPEN OPEN OPEN 220 sec. CLOSE OPEN OPEN CLOSE 2.8 FDC37C665/ALI M5113 Multi-I/O Chip The PSC-586VGA equipped with super multi-I/O chip SMC disable the multi-I/O Chipset. · JP14/JP15 : Multi-I/O Chipset Setting Enable/Disable MIO JP14 JP15 OPEN OPEN Disable FDC37C665 CLOSE OPEN * Enable M5113 OPEN 1-2 CLOSE 2-3 Disable M5113 The PSC-586VGA have built-in Cirrus GD54M30 PCI VGA Controller. If you want to use the external VGA Card,PCI or ISA bus,the BIOS will automatic disable the on board VGA controller and to use the external one. To get more VGA drivers information,please refer the Cirrus Internet address : 12 WWW.CIRRUS.COM 2.9 PCI VGA Controller (*) : default setting * Enable FDC37C665 FDC37C665 or ALI M5113, you can select JP14 or JP15 to enable or (*) : default setting PERIOD JP16: WDT Time-Out Period (*): default setting DISABLE WDT ACTIVATE NMI TO CPU WHEN WDT TIME-OUT Or BBS at Taiwan : Cirrus - 886 2 7185173 - 886 2 5147675 3 Connection 3.1 · PIN NO.DESCRIPTIONPIN NO.DESCRIPTION 12 34 56 78 910 1112 1314 1516 1718DIRECTION# 1920STEP# 2122WRITE DATA# 2324WRITE GATE# 2526 2728WRITE PROTECT# 2930 3132SIDE 1 SELECT# 3334 13 DISK CHANGE#GROUND GROUND READ DATA#GROUND GROUND TRACK 0#GROUND GROUND GROUND GROUND GROUND MOTOR ENABLE B#GROUND DRIVE SELECT A#GROUND DRIVE SELECT B#GROUND MOTOR ENABLE A#GROUND INDEX#GROUND N/CGROUND N/CGROUND REDUCE WRITEGROUND CN8 : FDC CONNECTOR connector cable. PSC-586VGA board equipped with a 34-pin daisy-chain driver Floppy Disk Drive Connector indicators to the PSC-586VGA board. This chapter describes how to connect peripherals, switches and 3.2 You can attach four IDE( Integrated Device Electronics) hard disk drives to the PSC-586VGA IDE controller. · DESCRIPTIONDESCRIPTION 1RESET#2 34 56 78DATA 10 910DATA 11 1112DATA 12 1314DATA 13 1516DATA 14 1718DATA 15 1920 2122 23IOW#24 25IOR#26 2728 2930 31INTERRUPT32 3334 3536 37HDC CS0#38HDC CS1# 3940 14 GROUNDHDD ACTIVE# SA2SA0 N/CSA1 IOCS16#-DEFAULT GROUND - DEFAULTN/C BALE - DEFAULTN/C GROUND GROUND GROUNDN/C N/CGROUND DATA 0 DATA 1 DATA 2 DATA 3 DATA 4 DATA 5 DATA 9DATA 6 DATA 8DATA 7 GROUND PIN NO.PIN NO. CN6/CN7: IDE Interface Connector CN6(IDE 2) : Secondary IDE Connector CN7(IDE 1) : Primary IDE Connector PCI E-IDE Disk Drive Connector 3.3 · DESCRIPTIONDESCRIPTION 1STROBE#2 34 56 78 910 1112 13PRINTER SELECT14 15ERROR#16 17PRINTER SELECT LN#18 1920 2122 2324 25 3.4 with Read/Receive 16 byte FIFO serial ports. · CN14 : Serial Port DB-9 Connector( ACE0 ) DESCRIPTION 1 2 3 4 5 6 7 8 9 15 RING INDICATOR (RI) CLEAR TO SEND (CTS) REQUEST TO SEND (RTS) DATA SET READY (DSR) GROUND (GND) DATA TERMINAL READY (DTR) TRANSMIT DATA (TXD) RECEIVE DATA (RXD) DATA CARRIER DETECT (DCD) PIN NO. The PSC-586VGA offers two high speed NS16C550 compatible UARTs Serial Ports GROUND GROUNDGROUND GROUNDGROUND GROUNDGROUND GROUND INITIALIZE AUTO FORM FEED # PAPER EMPTYBUSY ACKNOWLEDGEDATA 7 DATA 6DATA 5 DATA 4DATA 3 DATA 2DATA 1 DATA 0 PIN NO.PIN NO. CN10 : Parallel Port Connector CN10. on-board parallel port, accessed through a 26-pin flat-cable connector This port is usually connected to a printer, The PSC-586VGA includes an Port Parallel · CN13 : Serial Port 10-pin Header( ACE1) 3.5 · CN5 : 5-pin Header Keyboard Connector PIN NO.DESCRIPTION 1 2KEYBOARD DATA 3N/C 4GROUND 5 · PIN NO.DESCRIPTION 1KEYBOARD DATA 2N/C 3GROUND 4 5 6N/C 3.6 There are many external switches and indicators for monitoring and 16 controlling your CPU board. External Switches and Indicators KEYBOARD CLOCK +5V CN15 : 6-pin Mini-DIN Keyboard Connector +5V KEYBOARD CLOCK The PSC-586VGA provides two keyboard connectors. Keyboard Connector NC 10 GND 9 RI 8 DTR 7 CTX 6 TXD 5 RTS 4 RXD 3 DSR 2 DCD 1 Description Pin No. DescriptionPin No. · CN1 : POWER LED & KEYLOCK DESCRIPTION 1 2 3 4 5 · CN3 : RESET BUTTON DESCRIPTION 1 2 · DESCRIPTION 1+5V 2 The PSC-586VGA has its own buzzer, you also can connect to the external speaker through the connector CN2. · DESCRIPTION 1 2NC 3 4+5V 3.8 PS/2 Mouse 6-pin Mini-DIN Connector · DESCRIPTION 1 2NC 3 4+5V 5KBT1 6NC 17 GROUND MS DATA PIN NO. CN12 : PS/2 Mouse Connector GROUND SPEAKER SIGNAL PIN NO. CN2 : Speaker Connector 3.7 External Speaker HDD ACTIVE# PIN-NO CN4 : IDE LED connector GROUND EXTERNAL RESET PIN NO. GROUND KEYLOCK GROUND KEY POWER LED ANODE PIN NO. 3.9 VGA Connector The PSC-586VGA built-in 15pin VGA connector directly to your CRT monitor and a 26-pin header Feature Connector for any speical application,for example to drive EL flat panel. · 1RED2GREEN 34NC 56 78 9NC10 11NC12NC 13HSYNC14 15NC · 114PD0 215PD1 316PD2 417PD3 518PD4 619PD5 720PD6 821PD7 922 1023 1124 1225 1326 18 GroundNot Used Vertical SyncNot Used Horizontal SyncGround DAC BlankingGround DAC ClockGround Ground Not Used Select Internal Dot Clock Select Internal Sync Select Internal Video Ground Ground Ground CN9 : 13x2 26-pin Video Feature Connector VSYNC GROUND GROUNDGROUND GROUNDGROUND BLUE CN11 : 15-pin Female VGA Connector 4 AMI BIOS Setup configuration. The AMI BIOS setup program is designed to provide options which may be selected for end-user requirements. This chapter is written to assist you in the proper usage of these features. 4.1 Getting Start initialization and system configuration verification. After the POST routines are completed, the following message appears : 19 following screen will be displayed at this time. To access AMI PCI/ISA BIOS Setup program, press key. The " Hit DEL if you want to run SETUP" Test routines. These routines will be executed for system test and When power on the system, the BIOS will enter the Power-On-Self- maximum flexibility in configuring the system by offering various The PSC-586VGA uses the AMI PCI/ISA BIOS for system 4.2 Standard Setup The Standard Setup is used for basic hardware system configuration. The main function is for Date/Time setting and this setup. Mode Setting for >528MB IDE HDD When the IDE hard disk drive you are using is larger than LBA Please use the IDE Setup Utility in BIOS SETUP to install 20 the HDD correctly. mode.528MB,please set the HDD mode to Floppy/Hard Disk Drive setting.Please refer the following screen for 4.3 Advanced Setup This advanced setup is designed for customer‘s tuning best performance of the PSC-586VGA board. As for normal operation ‘t have to change any default setting.The default setting screen for the Advanced Setup. 21 is pre-setted for most reliable operation.Please refer the following customers don 22 - Will check or not check the keyboard exist when power on system. Primary Display : - Will not check display card when power on system. - Options for Enable/Disable - Turn on the PS/2 mouse function. When use the PS/2 mouse will use the IRQ12. - Will increase the video speed. When the installed add-on card‘s ROM address is as above address,you could enable the shadow to get higher operation performance.When you enable the shadow 640KB and 1024KB. 4.4 Chipset Setup This setup functions are almostly working for ChipSet(ALI M1511/M1512/M1513). These options are used to change the ChipSet‘s registers. Please carefully change any default setting ,otherwise the system could be running un-stable. 23 function,it will also reduce the memory available by between Shadow C8000-CFFFF,D0000-D7FFF,& D8000-DFFFF : Enable Video Shadow C000,32K: Mouse Support : different display device. VGA/EGA,CGA40x25,CGA80x25,or Mono Absent Absent/Present System Keyboard : AT Bus Clock : 7.16Mhz : The default setting will be fixed at 7.16Mhz bus clock even installed different speed CPU. CLK/4,5,6,8,10,12 : 24 CPU clock(50MHz,60MHz,or 66Mhz, dependent on different CPU speed) divides 4,5,6,8,10,or 12 to get the AT Bus Clock. Parity error check for chipset : Enable/Disalbe : BIOS check the DRAM parity or not. Usually the DRAM module did not have parity function now. This setup is almost working for Multi-I/O Chip(ALI M5113 or SMC37C665). These options are used to change the ChipSet‘s 25 application need perfectly. registers. Please carefully change any default setting to meet your 4.5 Peripheral Setup - Setting the following ports on default value OnBoard FDC : Enable OnChip IDE : Enable Serial Port1 : 3F8H Serial Port2 : 2F8H Parallel Port : 378H ‘ optional setting. OnBoard FDC : Enable/Disable OnChip IDE : Enable/Disable Serial Port1 : Disable/3F8H/3E8H/2E8H Serial Port2 : Disable/2F8H/3E8H/2E8H Parallel Port : Disable/3BCH/378H/278H 4.6 Power Management Setup Power Management Setup help user handles the PSC-586VGA ‘“green” function. The features could shut down the video display and hard disk to save energy for example. The power management setup screen is as following, 26 s board - customers choose the following portsManual Auto Programming Mode : The Watch-Dog Timer is provided to ensure that standalone systems can always recover from catastrophic conditions that caused the CPU to crash. This condition may have occurred by external EMI or a software bug. When the CPU stops working correctly, hardware on the board will either perform a hardware reset (cold boot) or a non- maskable interrupt (NMI) to bring the system back to a known state. The Watch-Dog Timer is controlled by two I/O ports. 443Enable the refresh the Watch-Dog Timer. (hex) 043Disable the Watch-Dog Timer. (hex) To enable the Watch-Dog Timer, a read from I/O port 443H must be performed. This will enable and activate the countdown timer which will eventually time out and either reset the CPU or cause an NMI depending on the setting of JP13. To ensure that this reset condition does not occur, the Watch-Dog Timer must be periodically refreshed by reading the same I/O port 433H. This must be done within the time A tolerance of at least 30% must be maintained to avoid unknown routines within the operating system (DOS), such as disk I/O that can 27 out period that is selected by jumper group JP16. Read Read Appendix A. Watch-Dog Timer be very time consuming. Therefore if the time out period has been set to 10 seconds, the I/O port 443H must be read within 7 seconds. Note: when exiting a program it is necessary to disable the Watch-Dog Timer, otherwise the system will reset. 28 10 11 20 30 40 50 60 70 80 90 1000 1070 2000 2070 5000 5010 5020 6000 6010 6020 29 RETURN X = INP( &H43) REM RESET WDT REM SUBROUTINE TO DISABLE THE WDT RETURN X = INP( &H443) REM ENABLE AND REFRESH TIMER REM SUBROUTINE TO ENABLE AND RESET WDT RETURN 3 SECONDS TO COMPLETE REM SUBROUTINE #2 RETURN 2 SECONDS TO COMPLETE REM SUBROUTINE #1 GOTO 30 GOSUB 5000 REM ENABLE AND REFRESH THE WDT GOSUB 3000 REM TASK 3, 5 SECS GOSUB 6000 REM DISABLE THE WDT GOSUB 2000 REM TASK 2, 3 SECS GOSUB 5000 REFRESH THE WDT GOSUB 1000 REM TASK 1, 2 SECS GOSUB 5000 REM ENABLE AND REFRESH THE WDT REM WATCH-DOG TIMER == WDT REM EXAMPLE PROGRAM